Chat Now

Welcome to online chat! If you have any questions or suggestions, please send them to us online, we will reply you as soon as we can!

Blog

Main Components and Structural Description of the CNC Press Brake

Jul 05, 2026

1. Ram Assembly: Utilizes hydraulic drive; the assembly consists of the ram, hydraulic cylinders, and a mechanical stop fine-adjustment mechanism. The left and right cylinders are fixed to the machine frame; hydraulic pressure drives the pistons (rods) to move the ram up and down, while the mechanical stop settings are controlled and adjusted by the CNC system. 2. Worktable Assembly: Operated via a push-button station, an electric motor drives the backgauge assembly to move forward and backward. The travel distance is controlled by the CNC system with a minimum resolution of 0.01 mm (limit switches are installed for both forward and backward travel limits). 3. Synchronization System: The machine employs a mechanical synchronization mechanism comprising a torsion shaft, swing...

Hot Tags : CNC Press Brake CNC System CNC Technology

Installation and Commissioning of CNC Press Brake Tooling

Jun 11, 2026

Installing and commissioning the tooling for a CNC press brake are crucial steps that must be completed before operation. Proper execution ensures optimal performance. Below are the key points regarding the installation and commissioning process: First, before installing the press brake tooling, adjust the equipment's settings and thoroughly inspect the machine to ensure there is no dust, metal shavings, or other debris that could interfere with operation. Second, when adjusting the ram stroke, verify that the tooling thickness meets specifications and that the ratio between the upper and lower dies is correct. Third, adjust the stroke modules and set the upper limit point correctly. In addition, parameters such as the bending angle and clearance must be precise...

Hot Tags : Press Brake Tooling

Bending Radius for Parts on a CNC Press Brake

Apr 10, 2026

When utilizing free bending, the bending radius is 0.156 times the die opening width. During the free bending process, the die opening width should be eight times the thickness of the metal material. For example, when forming low-carbon steel using a 1/2-inch die opening, the bending radius of the part will be approximately 0.078 inches. If the required bending radius is nearly as small as the material thickness, bottom bending (using a bottoming die) must be employed. However, the pressure required for bottom bending is approximately four times greater than that required for free bending. If the required bending radius is smaller than the material thickness, a punch with a nose radius smaller than the material thickness must be used, and the coining method of bending must be applie...

Hot Tags : bottoming die punch and die

8 Press Brake Machine Mistakes and How to Avoid Them

Feb 13, 2026

Something metal fabricators like to avoid is an upset ram. No, that’s not a distraught male sheep wandering in from the farm next door, it’s a press brake machine problem. The ram is an integral part of the press brake, and to say it’s upset means it’s bent. It’s bad news when parts of your machinery get bent because that makes it hard to form quality parts. Machines don’t have to be new to work well, but they do have to be cared for. Here’s a look at the importance of press brake maintenance. Putting in straight bends Sheet metal fabrications almost always go through the press brake. This is where we change it from sheet to a three dimensional shape. Those bends must be straight otherwise the final assembly won&rsqu...

Hot Tags : top tool bottom tool

How to avoid deviation in bending angle and size

Feb 06, 2026

For the bending process, the quality of the bending forming mainly depends on two important parameters: the angle and size of the bending. When bending, in order to ensure the forming size and angle of the bending, attention should be paid to the following aspects. (1) The misalignment of the upper and lower molds can lead to errors in bending dimensions. Before bending, it is necessary to adjust the alignment of the upper and lower mold tools. (2) After the left and right positions of the rear block are moved, the relative position between the sheet metal and the lower mold may change, which may affect the bending size. Before bending, the distance between the rear block positions needs to be re measured. (3) Insufficient parallelism between the workpiece and the lower mold can cause bend...

Hot Tags : upper and lower molds lower mold lower die V-groove tool clamping

4 Common Mistakes Made When Operating a Press Brake

Jan 29, 2026

The press brake is one of the most useful and common sheet metal machines used on a fabricating floor. Its versatility for bending a variety of materials in different thicknesses and compatibility with a wide range of different press brake tools makes it a staple piece that can solely achieve dozens of different bends and shapes. But if you don’t know what you’re doing, then, like any other sheet metal machine, a press brake can be a dangerous machine. Today’s article will highlight four common mistakes that are made by new press brake operators. 1. Performing pre-work checks Something that every operator should get in the habit of doing is performing pre-work checks to ensure that all elements of the machine are in appropria...

Hot Tags : press brake tools Press Brake Tooling

Bending Basics: 6 steps to successful die selection for press brakes

Nov 24, 2025

What inside bend radius you can achieve hinges on tonnage requirements and available die-opening widths Figure 1 To get the most out of your press brake tooling, the tangent of the bend, where the radius starts, ideally should be halfway down the die face. In this situation, half the die face is equal to the outside setback (OSSB), the distance from the outside mold line (planes that run parallel to the workpiece) to the tangent point of the bend. Question: Our fabrication department is documenting standard processes to select the correct punch and die combination to produce the desired results when air bending. We want to achieve a 90-degree bend for a 0.0751-in.-thick piece of 304 stainless steel with an inside bend radius that’s also 0.075...

Hot Tags : Press Brake Tooling punch die

Press Brake Basics for New Operators

Nov 09, 2025

Press brakes are advanced forms of fabrication technology used for bending sheet or plate material, most commonly sheet metal. Successfully using one requires a detailed understanding of how the machine functions and the role of the person operating it. If you’re new to working with press brakes, there are some important things to keep in mind: Types of Press Brake The two most common types of press brake are hydraulic and electric: Hydraulic Press Brakes: These are easier to use and come with a lower price tag. They are ideal for working with large, inexpensive materials that do not require high-precision bends. Typical pressure forces range from 40 to 600, and a hydraulic press brake will likely be your only option if you require a brake larger than 300 to...

Hot Tags : bending sheet or plate material V-Dies Gooseneck Punchs Offset Dies Acute-Angle Dies Multiple-Bend Dies

What material requirements should CNC press brake tooling meet?

Oct 23, 2025

To ensure the durability of CNC press brake tooling, the selection of materials is extremely stringent. Only materials that meet the following requirements are considered high-quality. 1. Wear resistance This is a basic and crucial material property. During the production process, intense friction occurs between the mold surface and the workpiece. If the material is not wear-resistant, the CNC press brake tools will easily become damaged and fail. 2. Toughness The working environment is relatively harsh, and the mold must withstand tremendous impact forces. Only strong and tough materials can withstand such impact without breaking. 3. High-temperature resistance CNC bending tool operate in high-temperature environments, which can reduce their hardn...

Hot Tags : Press Brake Tooling press brake tools CNC press brake tooling bending tool

A press brake is a machine capable of bending metal sheets

Oct 14, 2025

A press brake is a machine capable of bending thin sheets. Its structure primarily consists of a support, a worktable, and a clamping plate. The worktable is mounted on the support and consists of a base and a pressure plate. The base is hinged to the clamping plate. The base consists of a housing, a coil, and a cover. The coil is located in a recess in the housing, and the top of the recess is covered by the cover. During operation, a wire energizes the coil, generating an attractive force on the pressure plate, thereby clamping the sheet between the pressure plate and the base. The electromagnetic clamping mechanism allows the pressure plate to be shaped to various workpiece requirements and can process workpieces with side walls, making operation very simple. CNC press brakes and...

Hot Tags : press brake bending metal sheets worktable bending machine mold clamping

What are the types of press brake tooling （bending machine molds ）

Oct 13, 2025

Classification of commonly used press brake tooling: There are several types of bending tools, including L-shaped, R-shaped, U-shaped, Z-shaped, etc. The upper punch mainly has different angles such as 90 °, 88 °, 45 °, 30 °, 20 °, and 15 °. There are double and single slots with different slot widths of 4-18V in the lower dies, as well as R lower mold, acute angle lower mold, flattening tool set, etc. press brake tooling punch and die are divided into sections and whole parts: the upper punch is generally divided into sections of 300mm, 200mm, 100mm, 100mm, 50mm, 40mm, 20mm, 15mm, 10mm, and the whole is 835mm. The lower die is generally divided into sections of 400mm, 200mm, 100mm, 50mm, 40mm, 20mm, 15mm, and 10mm, and the whole is 835mm. ① Bending tools are made o...

Hot Tags : Press Brake Tooling upper punch press brake tooling punch and die flattening tool set bending machine molds tools storage cabinets

Maintenance and upkeep of the press brake

Oct 11, 2025

Before performing machine maintenance or cleaning, the upper punch should be aligned with the lower dies and the machine should be lowered and turned off until the work is completed. If startup or other operations are required, the mode should be selected as manual and safety should be ensured. The maintenance content is as follows: 1. Hydraulic oil circuit 1) Check the oil level in the fuel tank every week, and also check it after hydraulic system maintenance. If the oil level is below the oil window, add hydraulic oil; 2) The hydraulic oil used in this machine is ISO HM46 or MOBIL DTE25; 3) The new machine should have its oil changed after 2000 hours of operation, and every 4000-6000 hours of operation thereafter. After each oil change, the oil tank should be cleaned; 4) The syste...

Hot Tags : press brake machine tool Hydraulic components oil pipes upper punch lower dies